Like many British specialist manufacturers, AC Cars had been using the smooth, refined Bristol straight-6 engine in its small-volume production, including its AC Ace 2-seater roadster. This had a hand-built body with a steel tube frame, and aluminium body panels that were made using English wheeling machines. The engine was a pre-World War II design of BMW which by the 1960s was considered dated. Bristol decided in 1961 to cease production of its engine and instead to use Chrysler 331 cid (5.4 L) V8 engines. Although untrue, it is commonly believed that AC was left without a future source of power and that American ex-racing driver Carroll Shelby saved the company from bankruptcy. AC started using the 2.6 litre Ford Zephyr engine in its cars. In September 1961, Shelby airmailed AC a letter asking them if they would build him a car modified to accept a V8 engine. AC agreed, provided a suitable engine could be found. He first went to Chevrolet to see if they would provide him with engines, but not wanting to add competition to the Corvette they said no. Ford however, wanted a car that could compete with the Corvette and they happened to have a brand new thin-wall small-block engine which could be used in this endeavor. It was Ford's 260 in³ HiPo (4.2 L) engine – a new lightweight, thin-wall cast small-block V8 tuned for high performance. Ford provided Shelby with two 260ci engines. In January 1962 mechanics at AC Cars in Thames Ditton, Surrey fitted the prototype chassis CSX0001 with a 260ci Ford V8; the 221ci was never sent. However, early engineering drawings were titled "AC Ace 3.6". After testing and modification, the engine and transmission were removed and the chassis was air-freighted to Shelby in Los Angeles on 2 February 1962. His team fitted it with an engine and transmission in less than eight hours at Dean Moon's shop in Santa Fe Springs, California, and began road-testing.
the 1966 Shelby Cobra 427
AC's system was as follows: The Ace chassis numbers read AEX... "A" being the car series and "X" being for export with left hand drive. Later with the introduction of the Bristol engine the chassis numbers ran "BEX..." When switching to the Ford 2.6 engine the Ace chassis numbers ran "RS..." for Ruddspeed as Ken Rudd may have been influential in the choice of engine. The first Cobra chassis was left hand drive and given the next letter in the alphabet,i.e. C. Therefore the numbers ran CSX2... for all the export Cobras. Otherwise, the prefix was "CS2...". The four following numbers ran from 2000 sequentially. When the MKIII Cobra was built the identification ran from CSX3000 (for left hand drive export). There were other numbers used such as "COB...." and "COX...".
1966 Ford 427 Shelby Cobra
Production proved to be easy, since AC had already made most of the modifications needed for the small-block V8 when they installed the 2.6 litre Ford Zephyr engine, including the extensive rework of the AC Ace's front end. The most important modification was the fitting of a stronger rear differential to handle the increased engine power. A Salisbury 4HU unit with inboard disk brakes to reduce unsprung weight was chosen instead of the old ENV unit. It was the same unit used on the Jaguar E-Type. On the production version, the inboard brakes were moved outboard to reduce cost. The only modification of the front end of the first Cobra from that of the AC Ace 2.6 was the steering box, which had to be moved outward to clear the wider V8 motor.
427 Cobra Country--Ford AC
Shelby Cobra. by admin
Shelby Cobra
1967 Shelby Cobra picture,
the 1966 Shelby Cobra 427
AC's system was as follows: The Ace chassis numbers read AEX... "A" being the car series and "X" being for export with left hand drive. Later with the introduction of the Bristol engine the chassis numbers ran "BEX..." When switching to the Ford 2.6 engine the Ace chassis numbers ran "RS..." for Ruddspeed as Ken Rudd may have been influential in the choice of engine. The first Cobra chassis was left hand drive and given the next letter in the alphabet,i.e. C. Therefore the numbers ran CSX2... for all the export Cobras. Otherwise, the prefix was "CS2...". The four following numbers ran from 2000 sequentially. When the MKIII Cobra was built the identification ran from CSX3000 (for left hand drive export). There were other numbers used such as "COB...." and "COX...".
1966 Ford 427 Shelby Cobra
Production proved to be easy, since AC had already made most of the modifications needed for the small-block V8 when they installed the 2.6 litre Ford Zephyr engine, including the extensive rework of the AC Ace's front end. The most important modification was the fitting of a stronger rear differential to handle the increased engine power. A Salisbury 4HU unit with inboard disk brakes to reduce unsprung weight was chosen instead of the old ENV unit. It was the same unit used on the Jaguar E-Type. On the production version, the inboard brakes were moved outboard to reduce cost. The only modification of the front end of the first Cobra from that of the AC Ace 2.6 was the steering box, which had to be moved outward to clear the wider V8 motor.
427 Cobra Country--Ford AC
Shelby Cobra. by admin
Shelby Cobra
1967 Shelby Cobra picture,
No comments:
Post a Comment